Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Hang on, your tank is 80 x 60 and it's going on a 70 x 70 cabinet? lol
-
You are viewing the forum as a Guest, please login (you can use your Facebook, Twitter, Google or Microsoft account to login) or register using this link: Log in or Sign Up
DIY Project DIY ADA Style Aquarium Stand
- Thread starter Deano3
- Start date
Hang on, your tank is 80 x 60 and it's going on a 70 x 70 cabinet? lol
Lindy
Member
No the frame is made out of 70mmx70mm square timber mm being millimetres? The stand is obviously 80x60cm. I didn't want to trust in mdf and my dodgy diy so there is a very sturdy frame at the heart of it. Similar style to alistairs last chocolate tank.
Sent from my GT-I9505 using Tapatalk
Sent from my GT-I9505 using Tapatalk
James O
Member
I think he means 70mm timber used for a 80x60cm cabinet 😉
Edit: d'oh! Ya beat me to it
Edit: d'oh! Ya beat me to it
James O
Member
Whoops! Sorry Lindy. I thought it was Deano3.......
Lindy
Member
I would have liked to put wheels on it as its going to be a heavyweight beast but that would sky rocket the price.
Sent from my GT-I9505 using Tapatalk
Sent from my GT-I9505 using Tapatalk
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Even with wheels on I wouldn't fancy moving a large'ish fish tank around full of water lol, swish, swish, ooops, where's my fish (gone)! lol 🙂
Lindy
Member
I meant just for moving the stand lol. We are hoping to move this year so this will all have to be shifted 😱
Sent from my GT-I9505 using Tapatalk
Sent from my GT-I9505 using Tapatalk
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
I think i'll just shut up then
lol, highlights my inability to understand the opposite sex 
Nathaniel Whiteside
Member
I think i'll just shut up then
Common complaint
Lindy
Member
I thought it was men that always say ''my wife doesn't understand me'' 🙄
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
It's the same thing LOL
James O
Member
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Finished sanding off the edges tonight so applied some watered down white emulsion as a primer. Seemed to take ok. Guess I'll do this a time or two before sanding off and thinking about undercoat.
Not quite sure what undercoat to use, probably try some normal wood stuff see how that takes 🙂
Not quite sure what undercoat to use, probably try some normal wood stuff see how that takes 🙂
Attachments
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Also thought as quite a resorceful thread I'll add some extra photos...
Drilling the holes to fit hinges to the doors, after looking all over for the measurement to drill these and finding a blum tech sheet, i drilled my 35mm holes (with a forstner bit) 22.5mm centre from the edge of the door panel, 4 inches down from top/up from bottom. Got to be quite careful as the holes needed to be about 14mm deep (in 18mm door) and with a small pilot bit on the forstner drill bit, it almost came through the front of the door, this will depend on the drill bit you use.
I then fitted the hinges to the doors.
After screwing the hinges into the door I fixed on the mounting plates (that screw onto the cabinet sides) and put all hinges in closed position.
To get the correct position for the mounting brackets was simply a case of propping the door in it's closed position against the cabinet, using screwdrivers, scrapers, bascially anything I could to pack it out into the position it would be in when closed. Once happy with all gaps at the side, top etc, I drew around the mounting plates on the cabinet sides with a pencil, then removed the mounting brackets from the rest of the hinge, put them inside my pencil marks and marked the centres for the mounting bracket screws. I believe you can get a blum mounting template that does all this for you. *Note - doing it the way I did, i got a good fit, but did have to use all the hinge adjustment available to get the doors flush to the top panel so in hindsight I should have set the mounting bracket 2mm back from my where my marks were, but hey, it's worked out ok.
I then offered up the left hand door whilst the right hand door was still on, to ensure gaps between the doors were good, once lined up and the left door gently packed and held in position (as the right one was) i removed the right hand door so i could get in to draw a pencil round the brackets for the left door. I then just did the same for this door as the other (so again had to use all adjustment for getting doors flush!), and when all done...
Da-daaaaaaaaaaaa 🙂
Cheers,
Rob
Drilling the holes to fit hinges to the doors, after looking all over for the measurement to drill these and finding a blum tech sheet, i drilled my 35mm holes (with a forstner bit) 22.5mm centre from the edge of the door panel, 4 inches down from top/up from bottom. Got to be quite careful as the holes needed to be about 14mm deep (in 18mm door) and with a small pilot bit on the forstner drill bit, it almost came through the front of the door, this will depend on the drill bit you use.
I then fitted the hinges to the doors.
After screwing the hinges into the door I fixed on the mounting plates (that screw onto the cabinet sides) and put all hinges in closed position.
To get the correct position for the mounting brackets was simply a case of propping the door in it's closed position against the cabinet, using screwdrivers, scrapers, bascially anything I could to pack it out into the position it would be in when closed. Once happy with all gaps at the side, top etc, I drew around the mounting plates on the cabinet sides with a pencil, then removed the mounting brackets from the rest of the hinge, put them inside my pencil marks and marked the centres for the mounting bracket screws. I believe you can get a blum mounting template that does all this for you. *Note - doing it the way I did, i got a good fit, but did have to use all the hinge adjustment available to get the doors flush to the top panel so in hindsight I should have set the mounting bracket 2mm back from my where my marks were, but hey, it's worked out ok.
I then offered up the left hand door whilst the right hand door was still on, to ensure gaps between the doors were good, once lined up and the left door gently packed and held in position (as the right one was) i removed the right hand door so i could get in to draw a pencil round the brackets for the left door. I then just did the same for this door as the other (so again had to use all adjustment for getting doors flush!), and when all done...
Da-daaaaaaaaaaaa 🙂
Cheers,
Rob
Attachments
Wallace
Member
Looks good Rob, nice job with the hinge hole cutter.
I would of thought you'd have opted for soft close Blum hinges though?
Sent from my iPhone using Tapatalk
I would of thought you'd have opted for soft close Blum hinges though?
Sent from my iPhone using Tapatalk
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Wallace
Member
You've not got the piston clipped on. D'oh!
I blame manflu.
Sent from my iPhone using Tapatalk
I blame manflu.
Sent from my iPhone using Tapatalk
Rob P
Member
- Joined
- 13 Oct 2013
- Messages
- 785
Exsqueeze me? lol. The only things missing are the shiny cover caps (and these won't be clipped on until position is final), these are blumotion softclose things (it's all built into the mech). You can see a little black switch on the door side of the hinge that switches the soft close on or off 😉
Wallace
Member
Ah ok. They've changed since I last sold them in a kitchen.
As you were.
Sent from my iPhone using Tapatalk
As you were.
Sent from my iPhone using Tapatalk
