• You are viewing the forum as a Guest, please login (you can use your Facebook, Twitter, Google or Microsoft account to login) or register using this link: Log in or Sign Up

Eheim skim 350 problems

EA James

EA James

Member
Joined
22 Jul 2019
Messages
567
Location
Staines-upon-Thames
Hi all,

I have recently bought the above and i have two issues i'm hoping can be resolved.

Firstly, i can only run it on the lowest setting or all it does is spray out bursts of bubbles, very annoying! Surely it should be able to work at higher pressure without blasting bubbles out?

Secondly, The two times I've cleaned it (on WC day) I've found a dead Rummynose tetra in it on both occasions so is there a mesh or something i can put over the intake to stop this happening? Or maybe putting it on a timer so the trapped fish could escape when it goes off?

Does anyone else have this skimmer that can offer a solution?

Cheers, James
 
Many people have reported both of these problems.
Lowest to medium setting is all it will work on without sucking in bubbles. As to killing fish and shrimp, I used a timer and had it run for only 5mins every hour. Others have made or bought or 3D printed guards to stop critters being sucked in. If you search on here, there are threads about this.
 
hypnogogia said:
Many people have reported both of these problems.
Click to expand...
I wonder if Eheim are aware of these? Might be worth putting an email together to see what they have to say.
Poor design is not something you'd associate with a name like Eheim , surely they test them before mass production?!!

I'l have a search about on the forum to see what i can find
Thanks for the info
 
I have the top of mine below the water level just enough to create a vortex as is pulls in the water. Its a pain to get right but it cures the bubble issue.

Hope i make sense.
 
I used to get this when the supplied sponge was new or cleaned.
Also found the supplied sponge disintegrates fairly quickly,when using co2.
I swapped it out,for a piece of medium density sponge I had lying about..which solved the issue.
Food being sucked in,will lure critters..so I always switch off when feeding,unless it's a strictly sinking food.
 
Andy Taylor said:
I have the top of mine below the water level just enough to create a vortex as is pulls in the water. Its a pain to get right but it cures the bubble issue.

Hope i make sense.
Click to expand...
You mean the actual unit just below water level I’m guessing? So the floating bit isn’t extended to the surface?
 
EA James said:
You mean the actual unit just below water level I’m guessing? So the floating bit isn’t extended to the surface?
Click to expand...
Correct. Works fine for me. The brown thing is an old media bag i cut down to stop my curious shrimp from being shredded.
 

Attachments

  • Skimmer.JPG
    Skimmer.JPG
    52 KB · Views: 640
@Andy Taylor and that works alright for you? I tried the same thing with a fruit and veg mesh bag from Sainsbury’s but for some reason it didn’t work. Maybe it’s because I still had it on the lowest output setting?
I’ll try repositioning later
Cheers matey
 
I don’t use mine anymore. It’s a pretty badly conceived product in my opinion. Who on earth would design an electrical product with the cable facing downwards when they know it has to go upwards out of the tank? There are other better looking products out there but they’re not generally available in Europe.

Anyone know if the ADA ones with the float switch inside work any better than the Eheim?
 
Aqua sobriquet said:
Anyone know if the ADA ones with the float switch inside work any better than the Eheim?
Click to expand...

Use an ADA Vuppa 2 on a Aquascaper 1200. Works for the purposes I require it for (rids minor dust accumulation on the surface across time), but as a skimmer for film and a pump for additional flow it would be a let down for many people’s expectations.

In the case of the OP’s objection to livestock being sucked in using the eheim skim, have yet to find anything in the Vuppa as it has a small slit that draws water in and is very low lph compared to the eheim skimmer.
 
Aqua sobriquet said:
Who on earth would design an electrical product with the cable facing downwards when they know it has to go upwards out of the tank?
Click to expand...
I thought that, it makes it look messy and because of that the unit sits a bit of an angle which really irritates me. The suckers aren't strong enough to keep it in place!
 
Andrew Butler said:
how have you got yours set heightwise in relation to your water level Geoff?
Click to expand...
It works on a slider to adjust height. Set it so the top rim of the unit is just affecting the surface tension of the water, but the surrounding water is all being pulled towards the slit/intake so only enters there.

Setting up the Vuppa carefully like this avoids the knocking on/off sound people report from the float switch engaging/disengaging the pump. You get smooth, silent running.
 
For problem one; make sure the pump is fully submerged, and that the inlet is floating to the surface - press the inlet down so that it is fully submerged, and when there is no air bubbles in the water release.

I run on full power, no air bubbles 🙂
 
Geoffrey Rea said:
It works on a slider to adjust height. Set it so the top rim of the unit is just affecting the surface tension of the water, but the surrounding water is all being pulled towards the slit/intake so only enters there.

Setting up the Vuppa carefully like this avoids the knocking on/off sound people report from the float switch engaging/disengaging the pump. You get smooth, silent running.
Click to expand...
I've started a thread on the Vuppa II to keep it separate, hopefully you can have a look through and reply @Geoffrey Rea 😉
Geoffrey Rea said:
silent running
Click to expand...
Uninterestingly Mike & the Mechanics sprung straight to mind!
 
Last edited:
You must log in or register to reply here.
Back
Top